How does the Win8 system use the bearer network?

1. First confirm that the wireless network card switch is turned on, the driver has been successfully installed, and the wireless network function can be used normally.

Open the Control Panel --- View network status and tasks, click on the "Change Adapter Settings" on the left side, confirm that there is a "Wi-Fi" network connection. As shown below:

Right click on the desktop <; Computer" icon to select “Set" "Device Manager" or press “Windows" and “X” Key, select "Device Manager", confirm "Network Adapter" under the device with no exclamation mark, there is a wireless network card device and "Microsoft Kernel Debug Network Adapter", as shown below (different brands of different models of wireless network card The names are slightly different. The following figure uses the Atheros AR9285 as an example. If you do not have these two devices, please uninstall the existing wireless network card driver and reinstall the Lenovo website to provide the wireless network card driver.

If you have a down arrow icon, right click on this device and select On. As shown below:

If there is an exclamation point with "wan miniport", please refer to the note explanation.

Click the network icon in the task bar at the bottom right corner. If there are other network signals around, the wireless network card is available.

2. Determine if the network sharing related service is enabled.

Right-click on the desktop <;computer” icon, and then click "Manage"---"Services & Applications>;---"Service” (or press “ Windows key and R key", enter “services.msc”, click OK to open “service manager”), view "Internet Connection Sharing (ICS)" and "Remote Procedure Call (RPC)” Whether the service is enabled. If “manual"not" is running”, right click on the corresponding service <;start”;if “disable”, corresponding service right click on “property",“start mode&rdquo ; set to “automatic", click the "application" button, click “start”, then click “OK" to complete the setup.

3. Set up the bearer network.

Simultaneously press the Windows and X keys and select “Command Prompt (Administrator)”.

Enter netsh wlan set hostednetwork mode=allow ssid=The name of the network you want to create (in English) key=The password you want to set (at least 8 digits) Press Enter to set the ssid and password. (For example, netsh wlan set hostednetwork mode=allow ssid=mywlan key=12345678.)

Enter netsh wlan start hostednetwork and press Enter to start the bearer network.

4. Set up network share

Open Control Panel---View Network Status and Tasks---Change Adapter Settings

If the above command is created successfully, a message will appear. “Local connection*” behind a digital network connection. And the middle part will display the set wireless network name. As shown below:

In the "Ethernet", right-click and select "Attributes", click "Share", click the settings shown below, click the "OK" button to save the settings. . (If you use a broadband connection to dial-up Internet access, please click “Select Properties” to set the share” in the “Broadband Connection” dialog box.

After the above operation is completed, the wireless network created by the mobile phone search “mywlan” will use the key ““ 12345678” connection test.

Remarks:

If the network icon in the lower right corner is turned on, "Wi-Fi" is displayed as "Off”

2. If Device Manager appears & ldquo;WAN Microport (Network Monitor)”

3. After entering the command and pressing the enter key, it is found that there is no "local adapter*" in the interface of the "Change adapter settings", first open again "Device Management" "Check if there is a "Microsoft Managed Network Virtual Adapter" is disabled, as shown below. If it is disabled, right-click and select “Enable”, then re-enter the command to create a wireless network. (Note: This virtual device appears only after the bearer network is created. It is normally hidden and invisible.)

If the above operation is completed, “Always connect*”, please open” Control Panel "-“System & Security"-“Windows Firewall", click on the left side" Allow Programs or Features via Windows Firewall", find the "Windows Communication Foundation" project, check to see if all are checked. After all check, click OK and try to recreate the wireless network.

If the mobile phone is connected to the created wireless network, but the webpage cannot be opened, firstly disable all the protection software installed on the computer or temporarily stop the protection, and then open the “Control Panel”---“ system And security "---“Windows Firewall", click on the left side <; turn Windows Firewall on or off", temporarily set to off, then try to re-open the page.

If the mobile terminal QQ can send and receive messages, but can not open the webpage, other applications can not be connected to the Internet, the computer system DNS service function may be abnormal, can be in the "change adapter settings" in the "Ethernet" /or “Broadband connection” (depending on the network used), right click and select “Status”, click “Details”, record “IPv4 DNS” information, manually set “DNS” in the mobile network settings. Server " (domain name) address. For details on how to set up, please refer to the instructions provided by the mobile phone manufacturer.

You can also consult your local network operator for the DNS server address used. The following public NDS server addresses can be used: 114DNS (114.114.114.114, 114.114.115.115), Google Public DNS (8.8.8.8, 8.8.4.4), OpenDNS (208.67.222.222, 208.67.220.220), depending on the region and use Network operators choose nearby.