Share the power on press F1 solution and cause analysis

Press F1 when booting, this is because your BIOS is not properly set but can also boot the system normally, it is a non-fatal fault, press F1 is Ask if you want to continue.

You have not installed the floppy disk drive, but set it in CMOS, open the floppy drive option. The method is: boot press the Del key, enter the BIOS settings, select the first "basic settings", floopy one The item setting is not invalid. Disabel" is invalid. 2 Just press DEL to enter the BIOS when you start the boot, press Enter to enter the first item, and see if the “Drive A” option is “None”, if not Press “Pgup” or “PgDn” to modify, press “ESC” to exit, select “Save & Exit Setup" and press Enter to exit the BIOS, reboot, then change the battery and press the above The steps are reset again. 3 boot need to press the F1 button to enter, mainly because the BIOS settings and real hardware data do not match, can be divided into the following situations: 1, there is actually no floppy drive or floppy drive is broken, but the BIOS is set to have a floppy drive This will cause you to press F1 to continue. 2, the original two hard drives, set up in the BIOS into a dual hard drive, and later lost one of them but forgot to change the BIOS settings back, this problem will also occur. 3. If the motherboard battery is not powered, it will cause data loss and this fault will occur. 4. Restart the system and enter the BIOS setup. The floppy drive is set to 1.44M, but there is actually no floppy drive in the chassis. After setting this item to NONE, the fault is rectified. There have been many people who have asked such questions. Let me summarize the problems I have encountered and hope to help everyone. 1, Hareware Monitor found an error, enter POWER MANAGEMENT SETUP for details, Press F1 to continue, DEL to enter SETUP

中文: The monitoring function found an error, enter POWER MANAGEMENT SETUP to view the details, press F1 to continue booting Program, press the DEL key to enter the COMS settings.

Explanation: Some motherboards have hardware monitoring functions, which can set the temperature monitoring of the motherboard and CPU, the voltage output level monitoring of the voltage regulator, and the monitoring of each fan speed when

The above monitoring function finds an abnormal situation when the power is turned on, then the above paragraph will appear. At this time, you can enter the COMS setting and select POWER MANAGEMENT SETUP. On the right side, **Fan Monitor**, **Thermal Monitor** and * *Voltage Monitor** checks which part of the exception was issued and then resolved.

2, pri slave drive-ATAPI LNCOMPatible press F1 to Resume It may be that your CD-ROM drive is not connected or faulty. It is best to set each IDE port to automatic in CMOS.

3, Press F1 to continue, DEL to enter SETUP After booting, press DEL to enter BIOS. Select NONE in the selection floppy drive and press F10 to save it.

4, CMOS checksum error-Defaults Loaded Press F1 to contnue?DEL to enter SETUP 08/09/2000-i810-ITE8712-6A69ME1CC-00 The cmos battery is dead. 5, Warning! CPU has been changed! Please Enter CPU speed CMOS setup and Remember to save Before Exit! This means that the BIOS settings have been flushed and the BIOS (also called CMOS settings) has to be reset. Press and hold the “Del” button to enter the settings and see your motherboard manual. What is your CPU frequency? In the BIOS to choose a FSB, the multiplier is locked. The FSB is always 66, 100 or 133. It depends on the CPU model and is set from low to high. If it is AWARD's BIOS setting, select Frequency/Voltage Control on the front page. Use this menu to make special settings for frequency and voltage. Among them, “Clock By Slight Adjust” allows you to select the CPU clock frequency. There are differences in the BIOS settings of various motherboards. You can refer to your motherboard manual for adjustment. 6, cpu has been changed please re-enter cpu settings in the cmos setup and remember to save before quit! Some motherboards have a FSB jumper, the default is 100MHZ, and some motherboards do not support auto-tuning. You just enter the BIOS Set the FSB to your CPU standard FSB. The multiplier is usually set automatically. It is best not to overclock.