TP-Link router detailed installation settings seem simple in some people's eyes, but in most people's eyes it is difficult, the following small series from line connection, computer configuration, router configuration, The wireless network is configured with a few steps to explain how to install and set up a TP-Link router. 1. There are two types of ports connected to the line: WAN port and LAN port. The WAN port is connected to the WAN. The WAN is, in layman's terms, the external network we usually call. The WAN port should be connected to the outside. Simply put, which port the computer's network card is connected to, and which port the WAN is connected to. As shown in the above figure, if the phone is dial-up, the WAN port is connected to the cat; if there is a cell broadband port, the WAN port is connected to the cell broadband port. TP-Link router physical connection diagram 2, computer configuration This step is to prepare for step 3. The main thing is to ensure that the computer and router can communicate normally to configure the router. Under normal circumstances, as long as the router and computer are connected properly, the router will automatically assign an IP address to the computer, so this step can be skipped for most computers. If you cannot log in to the router management interface in step 3, follow the steps below. Windows 2000/XP system: Double-click the local connection in the lower right corner of the desktop of the computer. The small computer icon (if there is no network card icon in the lower right corner of the computer, enter the method as "start – control panel – network connection & ndash; double-click local connection&ldquo ;), then configure as shown below. Windows 7/Vista system: Click the network connection icon in the lower right corner of the desktop, click "Open Network and Sharing Center – Change Adapter Settings/Manage Network Connections– right click Local Connection & ndash; Attributes" (or click & rdquo; Start Button – Control Panel & ndash; Network and Internet & ndash; Network and Sharing Center & ndash; Change Adapter Settings /Manage Network Connections & ndash; right click on Local Area Connection & ndash; Attributes & ldquo;), then configure as shown below. After the above configuration, your computer will automatically ask the router & rdquo; IP address, the router will also assign parameters to the computer after receiving the request, after successful, click the small computer icon in the lower right corner of the computer, in the local connection status In the "Support" tab, you can see the parameters obtained by the computer, as shown below (take XP system as an example): 3. Router configuration 1 Open the web browser and enter http://192.168.1.1 in the address bar to open the router. Management interface, enter the management account of the router in the pop-up login box (username: admin password: admin); 2 select & rdquo; setup wizard & ldquo;, click & rdquo; next & ldquo;; 3 select the correct way to access the Internet (common There are three types of Internet access: PPPOE, dynamic IP address, and static IP address. Please select your Internet access method according to the following description. PPPOE: Dial-up Internet access, stand-alone (when the router was not used before), use the broadband connection that comes with the Windows system. Dialing, the operator gave a username and password. This is the most common way to access the Internet. ADSL lines are generally the way to access the Internet. Static IP address: The front-end operator provides a fixed IP address, gateway, DNS, etc., and has applications on some fiber-optic lines. Static IP should input the IP address, gateway and other parameters given by the operator. Dynamic IP: Before using the router, the computer only needs to connect the line, do not dial, and do not need to set the IP address to access the Internet. In the community broadband, campus network, etc. There will be applications in the environment. Dynamic IP Direct Point & Next; "Next" on line 4 to set the wireless name and password (if it is a wired broadband router, this step is skipped); SSID is the router's wireless network name, you can set it yourself, it is recommended to use a combination of letters and numbers SSID. The wireless password is the identity certificate when connecting to the wireless network. After setting, it can protect the wireless security of your router and prevent others from smashing the network. Set your own wireless signal name and password, click ” Next & rdquo; Password should be easy to remember and have some complexity, try not to use ”123456″, ”abc” this simple password. It would be better if you could include some special symbols. 5 setup is complete. At this point, after seeing the IP address of the WAN port status, there is a specific parameter instead of 0.0.0.0, indicating that the router is connected to the Internet at this time. Try to open a website and see if you can open it. If you can open it, you're done. 4, wireless network configuration 1 set the wireless signal connected to the router. If you want to use a computer to connect to the router wirelessly, first make sure that your computer is equipped with a wireless network card and can work normally. For computers with different operating systems, the method of searching and connecting wireless signals is as follows: Windows XP system: Double-click the bottom right corner of the desktop. Wi-fi icon, then select the wireless signal of the router in the list of open signals and click Connect. Enter the previously set wireless password and click the Connect button (note the consistency of the two inputs and the case of the password). Windows 7/Vista system: Click the wireless network connection icon in the lower right corner of the desktop, select the wireless signal of the router in the list of open signals and click the Connect button. Then enter the previously set wireless password and click the OK button. 2 Set up a smartphone (for example, the Android system) to connect to the wireless signal of the router. Click on the smartphone's menu button, select System Settings, and select WLAN in the Settings menu. After turning on the WLAN function, select the name of the wireless router signal: Enter the set wireless password to connect successfully. If the wireless connection is successful but you can't access the network, you can try to manually specify the IP address of the phone by referring to the following figure. 3 Set up iOS devices such as iPad and iPhone to connect router wireless signals. Open the main interface of the iPad, select the “Settings” menu and click Wi-Fi to enter the Wi-Fi network interface. Then turn on the Wi-Fi master switch and click on the wireless signal of your own router in the wireless network list. Enter the previously set wireless password and click the Join button. When the corresponding SSID is displayed in the wireless signal list, “√”, you can use the iPad to surf the Internet. If you need to manually specify the IP parameters such as the IP address of the iPad, click the “>” blue button after the wireless SSID number in the wireless network list, and then click to the “Static” page to manually set the network parameters of the iPad. . After the above configuration, open a web page to see if it can be opened normally. If it is, the configuration is successful. This article comes from [System Home] www.xp85.com