The boot can not automatically start the system, after the f1 boot, and often automatically shut down, how is it going? Guiqiu pointing
System reloading tutorial:
u disk loading xp System tutorial
u disk installed Win7 system tutorial
u disk installed Win10 system tutorial
If not yet that estimate is the hardware problem. (The hardware that may be faulty: CPU, memory, power
or the problem of heat dissipation from the host.)
(1). The heat dissipation function of the computer host is not good;
(2). Or voltage instability caused;
(3). The reason for the computer memory card;
(4). Software problems installed in the system.
Third-party software installation
In order to reload the program, if the problem of the program is serious, it may cause an infinite loop of restarting the computer repeatedly, so that you cannot use the computer normally.
Solution: Press F8 when the computer starts up - select "Safe Mode" to enter the computer system, enter the system, and then open to enter the "Start" menu - "Settings" - "Control Panel" - "System"
- "Advanced" - Then select "Startup and Recovery", and finally remove the check box in front of "Automatic Restart" under "System Failure".
Power Problems
Fault Performance: There is an optical drive device and a recorder device in the computer component.
Fault Analysis: Although some of the power supplies have a nominal maximum power of 300 watts (300W), the actual power is quite different, plus the current
computer hardware
The power is large. When there are many accessories in one computer, the current output of such a power supply will fluctuate greatly, which makes the system automatically restart
.
Troubleshooting: It is recommended to replace the power supply with good quality and high power.
Memory Problems
Fault Performance: The memory used in computer assembly is bulk memory, which is normal when running normally, but when running large 3D games
or running Software that has a large memory requirement often suddenly restarts automatically.
Fault Analysis: Because the quality of some bulk memory is too much, the system often restarts suddenly and automatically, and many mainboards on the market now support dual-channel memory, if two memories If there is a difference in quality and performance, it may cause the system to be unstable. When it is necessary to run a relatively large game or software, a sudden automatic restart will often occur.
Troubleshooting: We enter the BIOS settings, set the memory "CL value" to 3 or 3.5, and appropriately reduce the system "FSB bus frequency", if the memory works in dual channel mode, it is recommended The good thing is to choose to buy the same brand of memory, so that the same performance balance can be guaranteed to run smoothly.
The "button" or "reset" button or tap the chassis front panel to prevent the failure.
Fault Analysis: This type of problem is a hidden fault and it takes an estimated time to check it out. However, such failures usually occur on computers for a long period of time, usually due to the weakening of the spring button on the main unit and the spring button on the restart button, or the button and the front panel of the chassis have a lot of dirt, causing the button position to be abnormal. A fault that causes an automatic restart or an automatic shutdown from time to time.
Troubleshooting: When the shutdown button and the reset button cannot be returned normally, it is recommended that you consider replacing the button assembly or using alcohol to clean the dirt between the button and the chassis panel.
Motherboard BIOS settings are confusing or improperly caused
Fault performance: When the system runs a large game or software, it will automatically shut down or restart automatically after about 10 minutes. Initially, U startup Xiaobian suspects that it will be CPU. The temperature is too high, and the CPU temperature can be tested in the normal range by software.
Fault Analysis: At present, many motherboards have built-in control chips, which can automatically control the CPU temperature and automatically shut down when the temperature is too high. However, if the BIOS warning temperature is set too low, the computer will automatically shut down.
Troubleshooting: Enter the BIOS settings and adjust the "shutdown temperature" value in the "pc health" option to solve the problem.
Patch Panel Problems
Fault Performance: The host computer is connected to the printer, scanner and speakers on a power strip. It is easy to restart automatically when the weather is wet.
Fault Analysis: Under normal circumstances, we will use the power strip to supply power to multiple computer equipment at the same time. When the quality of the power strip is not used for a long time, the elasticity of the spring of the jack is weakened. At the same time, due to rust and oxidation, the plug and the spring piece are in poor contact, causing the current to change abnormally. Once the current cannot effectively ensure the stable operation of the system, a sudden automatic shutdown problem occurs. Detailed http://www.tongyongpe.com/n/201608/1654.html can be used as a reference
Can you enter safe mode?
This situation may be a system boot error
There may be a bois problem.
System problem reloading
There is a problem with the system