Win2008 common problems and system basic settings

1. How to install Windows Server 2008? There are two ways to do this: one is hard disk installation, and the other is CD-ROM installation. Either way, it is recommended to follow the installation sequence from the low version to the high version, namely: Windows XP & mdash; — Windows VISTA & mdash; & mdash; Windows Server 2008. Otherwise it will be quite troublesome. The specific installation method is similar to the installation of VISTA. This blog has a detailed introduction. 2. Installed to the last step to prompt for a password, how can I lose N times? input error. Windows Server 2008 requires a more complicated password method. If you simply enter 12345678 or abcdefgh, that is absolutely not acceptable. The correct input should be: 8 or more passwords including English uppercase and lowercase letters, such as: Windows2008, absolutely passed smoothly. 3. How many ways do you currently activate Windows Server 2008? Which method do you think is better? Currently, there are three main activation methods for Windows sever 2008: 1. Automatic activation. There is no doubt that this is the most formal and is the first choice. 2. The phone is activated. It is also within the scope of Microsoft's permission, nothing more than a fee. 3. Replace activation. The replacement file can be activated, but the individual points are always uncomfortable because of the "Vista". 4. I heard what files to back up after activation? What is the use? Yes. The purpose of the backup is to avoid the trouble of reinstalling the system in the future. The specific method is —— 1. Back up the following two files and save the active CD-KEY (note: appdata is a hidden folder) \\Windows\\System32\\licensing\\pkeyconfig\\pkeyconfig.xrm-ms \\Windows\\ServiceProfiles\\NetworkService\\AppData\\Roaming\\Microsoft\\ SoftwareLicensing\\tokens.dat 2. Reinstall the system later, do not need to enter CD-KEY, do not connect to the network, find the above two files, right click on the attribute — — security & mdash; & mdash; advanced & mdash; & mdash; owner, change to administrator, close the window , then re-select the advanced & mdash; & mdash; permissions, modify the amdinistator to full control, so you can delete it. 3. Turn off the Software Licensing service and replace the above two files with the backup activation file (if you do not turn off the service, tokens.dat cannot be replaced). Restart your computer, enter the activation number, and activate it after a while. At this point you can connect to the network. 5. How can I use the serial number on the Internet to be alive? I analyzed that the key released by Microsoft in the previous burst was limited, and the number of activations of each key was limited. At present, the serial number (key) on the Internet has been used by a large number of first-time first-timers, reaching the limit of the maximum number of activations. Therefore, it is not recognized by Microsoft. However, Microsoft's trial period for Windows Server 2008 has been greatly relaxed (60 days), and when the activation deadline is approaching, under the administrator, run the slmgr.vbs -rearm command to reset the activation period [can be reset three times] , you can continue to use it for 240 days. In fact, the perfect crack will come into being when the deadline is not reached. 6. How to turn off UAC? Control Panel → User Account & Rarr; Open or Close User Account Control & Rarr; Unauthorize User Account Control (UAC) to help protect your computer. 7, how to cancel the boot press CTRL + ALT + DEL login? Control Panel & Rarr; Management Tools & Rarr; Local Security Policy & Rarr; Local Policy & Rarr; Security Options & Rarr; Interactive Login: No need to press CTRL+ALT+DEL→ 8. How do I cancel the shutdown reason selection that appears when I shut down? Start → run gpedit.msc → computer configuration → management template & rarr; system & rarr; display & ldquo; close event tracking program & rdquo; & rarquo; disabled. 9. How to achieve automatic login? Start → Run → enter “rundll32 netplwiz.dll, UsersRunDll” command to open the account window, first select the account to be automatically logged in, select "to use this machine, the user must enter the username and password" Enter the password for this account (provided you want to turn off UAC). 10. How do I cancel the default share for each boot? Import the following into the registry and restart (provided you want to turn off UAC). Windows Registry Editor Version 5.00 [HKEY_LOCAL_MACHINE\\SYSTEM\\CurrentControlSet\\Services\\Lanmanserver\\Parameters] "AutoShareServer"=dword:00000000 11. How to cancel IE enhanced security configuration? Server Manager & Rarr; Security Information & Rarr; Configure IE ESC & Rar; In the pop-up window, administrators and users choose to disable. 12. How to enable Vista theme? 1) Server Manager → Feature Summary & Rarr; Add Features & Rarr; Choose to install the desktop experience.