WINXP system installation complete optimization process (1)

After you install the system, after installing the driver, after installing the application software, how do you optimize the system is most suitable? I recommend the optimization system has been the next few points. Here I Only optimized for XPSP2. The specific optimization scheme is as follows: 1. It is to shut down the system restore. It is recommended to keep only the system restore of the C drive system disk. Other disks, such as D, E, F, etc. are all turned off, as follows: Open my Computer Properties System Restore Select a drive such as D drive, set it at the point, then turn off the system restore on this drive, check the front to close it, the other drive letter closes the analogy, see picture 1 600)makesmallpic(this ,600,1800);' src="/upload_files/article/18/201002/1_lw3uf__20057823344563198.jpg" width="395" height="600" border="0" /> 2. Turn off automatic update, because XPSP2 itself Bring the security patches required by the system. After the installation is complete, it is safe to not patch. Oh, the shutdown method is as follows: Open my computer properties to automatically update and close the automatic update. See picture 2 600)makesmallpic(this,600,1800);' src="/upload_files/article/18/201002/1_wmwag__20057823384556410.jpg" width="418" height="497" border="0" /> 3. Turn off the system hibernation. Open the desktop property screen saver power hibernation to remove the hook in front of the hibernate, please see the picture 3 600) makemsmallpic (this,600,1800); ' src="/upload_files/article/18/201002 /1_o1w8g__20057823401173471.jpg" width="404" height="445" border="0" /> Here I would like to remind you that some older motherboards support advanced power, which may cause the system to fail to shut down. This, you need to enable the advanced power in the advanced power supply to tick the front, now the new motherboard is no advanced power supply, huh, huh. 4. Turn off the system error report open my computer properties advanced startup failure and recovery send error report disable error The report is OK, see picture 4 600)makesmallpic(this,600,1800);' src="/upload_files/article/18/201002/1_4xzic__20057823433192024.jpg" wi Dth="323" height="312" border="0" /> 5. Close port 3389, the method is as follows: Open my computer properties remotely remove the two hooks inside to confirm, see picture 5 600) makesmallpic (this,600,1800);' src="/upload_files/article/18/201002/1_jw2wi__20057823444652858.jpg" width="416" height="492" border="0" /> 6. Set the virtual memory size, virtual The minimum memory is recommended to be 2 times of the physical memory, and the maximum value is generally set according to the remaining size of the disk space. Generally, the physical memory of 512-1024, the default virtual memory setting can be, if it is 128 and 256 physical memory needs to be set, 128 The recommended memory is 256-1000 and the memory of 256 is recommended to be 512-2000. The virtual memory is best not set in the system disk. It can be set in other disks. The specific setting method is as follows: Open my computer properties advanced performance advanced changes, It is best to restart the computer after setting up, please see picture 6 600)makesmallpic(this,600,1800);' src="/upload_files/article/18/201002/1_9wfbu__20057823493295154.jpg" width="340" height="434" Border="0" /> 7. Adjustment system System sound, open the small speaker on the table, right click to open the volume control, turn the volume control and waveform to the maximum, and tick the cd player and the line input two mute (reduced noise) See picture 7 600)makesmallpic(this ,600,1800);' src="/upload_files/article/18/201002/1_qznj3__20057823524185126.jpg" width="601" height="275" border="0" /> 8. Reduce the boot item. The setting method is as follows : Start running msconfig to enter, start, check the anti-virus software, firewall, input method. The other hooks are removed, OK, closed, and exited without restarting the computer. Note: Antivirus software Rising is the beginning of rav, Jinshan is the beginning of kav, Jiangmin may also be the beginning of kv, wheat coffee is the beginning of shstat, Norton's, it is not clear, it seems that

is N At the beginning, kavsvce.exe is Kaspersky. Firewall, rfw begins with Rising Firewall, kfw may be Jinshan, and. Input method 98/me/2000 input method is internat, XP/2003 input method is ctfmon please see picture 8

esmallpic(this,600,1800);' src=/upload_files/article/18/201002/1_wopvp__20057823535429630.jpg border=0> 9. Set the IP and subnet for the local connection, and speed up the booting speed. (Note that it is only suitable for single-user Internet users, not suitable for LAN). The method is as follows: Network Neighborhood Properties Local Connection Properties TCP/IP Protocol Properties Select Manual Assign IP: 192.168.0.1 Subnet: 255.255.255.0 OK, OK, restart the computer, see picture 9 600) makesmallpic(this,600,1800);' src=/upload_files/article/18/201002/1_3p8wx__2005782356447445.jpg Border=0> 10. Reduce the scroll bar to speed up the boot speed optimization. Please download the following optimization file, directly open the import registry 600)makesmallpic(this,600,1800);' src=/upload_files/article/18/201002/1_nw8nu__rar.gif border=0> Click to browse the file 11. Increase the refresh rate, the CRT monitor suggests a refresh rate of 85, and the LCD monitor is recommended to set to 75 specific settings as follows: Open the table The face attribute sets the advanced monitor refresh rate setting. See picture 10 600) makesmallpic(this,600,1800);' src=/upload_files/article/18/201002/1_ewcif__20057911383699403.jpg border=0> 2005-7 -8 23:57:50