Win2000 Diskless Terminal Installation Guide

First, install Win2000 server

1. Please install Win2000 ADVANCED SERVER or Win2000 SERVER on your server. Note that the date is adjusted backwards by 10 years or longer (2010) before installing the server. After we have set all the settings below, we can adjust back to the correct date, so that the end user's date limit can be solved.

2, assuming the server name GCSERVER, you must add TCP /IP, IPX /SPX, NETBEUI, DLC protocol for the system, where the IP address is specified as: 192.168.10.1, the subnet mask is unified: 255.255.255.0 . Note that this server must be the primary domain.

Since Win2000 SERVER no longer provides RPL service, we must borrow special software to add remote boot service to Win2000 SERVER. Now there are many such tools in China. I recommend Lingxin remote boot tool to everyone. , it's the latest version v 3.0. Safe and stable and it is free. Of course, if conditions permit, I would like to use a WinNT4 remote boot server for booting of diskless workstations, and Windows 2000 Server servers for terminal services. This arrangement will make the entire network more stable and fast. However, the average user rarely has this economic ability. I use a Windows 2000 Server server as an example. The installation process is as follows:

Second, install RPL remote boot service

1. Copy the downloaded file to the server and put the NT40 Server CD into the server. In the optical drive. Refer to the prompts to fill in the path correctly.

2. After restarting Windows2000. An MgrPatch.exe file can be found in the installation directory. It is the Remote Boot Manager Monitor, which creates a shortcut to the desktop and must be used later to launch the Remote Boot Manager. Enter the command line mode of WINDOWS2000, CD RPL (that is, the target path when you add the remote boot service above). Execute RPLCMD and add the configuration to your workstation according to the same method of adding NIC parameters in NT4 (see the full diskless WIN95 installation). Set up diskless DOS622 to ensure that it can log in normally.

About the powerful features of METAFARM V1.8.

1. Install the system components, select the terminal service, do not authorize the terminal. Program running mode selection: Application mode. Compatible mode selection: TERMINAL 4.0 compatible mode. The system tells OFFICE 2000 that it may not work properly, regardless of whether it can be used.

2. Start installing METAFARM V1.8. After installing, install the METAFARM V1.8 patch from Add/Remove, it can't be installed directly. Many programs should be installed like this: WPS2000, etc. . Restart.

3, run the registration machine, if there are other protocols, delete it (REMOVE button), add (ADD button) the following protocols are enough, pay attention to the number of users (USER), Then activate again (ACTIVE).

Main Agreement (File Cabinet Type): OEM METAFRAME 1.8 FOR WIN2000 Number of Users: 100
Extended Protocol (User Type): CITRIX USER LICENSE PACK Number of Users: 100
Sub-Extension Protocol (Key Type) ): CITRIX LOAD BALANCING SERVICES Number of users: Can't change!
Sub-extension protocol (key type): CITRIX INSTALLATION MANAGEMENT SERVICES Number of users: Cannot be changed!
Sub-extension protocol (key type): WINFRAME SERVER OPTION PACK Number of users: Can not be changed!
Sub-extension protocol (key type): METAFRAME RESERVED OPTION PACK1 Number of users: Cannot be changed!
Sub-extension protocol (key type): METAFRAME RESERVED OPTION PACK2 Number of users: Cannot be changed!
Sub-extension protocol (key type): METAFRAME RESERVED OPTION PACK3 Number of users: Cannot be changed!
Sub-extension protocol (key type): METAFRAME RESERVED OPTION PACK4 Number of users: Cannot be changed!
Sub-extension protocol (key type): METAFRAME 1.8 FEATURE RELEASE 1 Number of users: Cannot be changed!
Sub-extension protocol (key type): METAFRAME 1.8 FEATURE RELEASE - UPDATE Number of users: Cannot be changed!
Description: There can be only one master protocol and one extension protocol, and there can be multiple extension protocols.

4. Enable the MetaFrame Tools ICA Client Creator project under the program menu. Unzip the client program (DOS 286 processor) to a floppy disk and copy it to the C:WINNTplRPLFILESPROFILES directory to create the CLIENT directory. Start a workstation, log in as ADMINISTRATOR, enter diskless DOS, enter the CLIENT directory, and start the installation. INSTALL+Enter, F1, Enter.

5. After installation, enter C:WFCLIENT directory, run WFCLIENT and configure parameters
Description: Just fill in, such as win2000
Transport : Press the triangle, select NETBIOS
Before the server (), there is an * number. The name below is added to the square extension, which should be the name of your server.
Username: Fill in a user account name
Password: Password
Domain:
Command line:
Working Directory:
[ x] Use data compression
[ x] Enable Sound

Then enter the main interface, select Preferenc under OPTIONS... Set the corresponding color, don't forget to enable the local mouse.
Go back to the main interface and select CONNET to log in.

6, then add a MOUSE.COM to the C:WINNTplRPLFILESPROFILES directory on the server, then open the AUTOEXEC.BAT file, add the following three lines at the end

@MOUSE
@cd WFCLIENT
@WFCLIENT win2000 /BATCH

7. Restart each workstation and you can see that each workstation can log in with the same USER user account.