Problems and solutions for Win2000 terminal

After installing and setting up according to the relevant content of this site, Windows 2000 terminal can be started, but some faults may be encountered during the installation process. This article will analyze various faults. And propose a solution. In addition, there are still some problems in the terminal technology in practical applications, such as the installation of application software, the addition of Chinese character input method, server security problem, multi-user automatic login and DOS program compatibility, etc. This paper proposes a reasonable solution to the above problems.

1. Common Faults and Handling

(1) Fault 1: When installing Windows 2000 Server, the system prompts "Invalid NetBIOS Name"

(2) Fault 2: When the server upgrades the domain, the installation of Active Directory (Active Directory) fails, the system prompts: Can not access the network location...

(3) Fault 3: Lingxin W2KRPL (Windows 2000 RPL patch) installation After the completion, restart, the system prompts to find an error, when the remote management program is started, it prompts "The remote startup service is not started". When the remote startup service is manually started in the "service" of the management tool, the system prompts: error 998, memory allocation is invalid. .

(4) Fault 4: When creating a new configuration file, the DOS boot record cannot be found in the configuration drop-down list (note that it is available before adding the network card)
(5) Fault 5: Install MetaFrame 1.8 a system prompts the following error message: MateFrame is designed to work on windows 2000 (Network operting System Version 5.0)
<6> (6) Fault 6: The terminal displays a blue screen error such as COM PORT when connecting to the server under DOS However, after hitting the car, you can log in to the server and use it normally. You cannot use the mouse after entering.

(7) Fault 7: When connecting to the server under IPX protocol under DOS, the following error message appears:

Connecting to 'w2k' (w2k is the connection name)

Support not available for IPX check you system configureation

(8) Fault 8: When the RPL diskless DOS workstation is connected with 256 colors 800x600, the ICA boot screen will crash and it will connect normally when it is 16 colors 640x480.

(9) Fault 9: After installing wfw311, the diskless DOS workstation cannot be started, execute to

NET START RDR /RPL:YES /FIT:YES /COMPUTERNAME:(COMPUTER_NAME) /When HIMEM: YES, the following prompt appears: General failure writing drive cAbort, Retry, Fail?

Fault 10: After installing Windos32, the mouse can not be used, but in the DOS state can be driven normally, and can be used under the application.

(10) Fault 11: After entering WIN2000 on the workstation, the mouse has to wait for about 30 seconds to work.

(11) Fault 12: Terminal client common user account login server When logging in, the warning box "This system's local policy does not allow you to use interactive login" appears. After "OK", it returns to the original operating system and cannot connect to the server.

2, application software installation and use problems

After the Windows 2000 terminal system is successfully installed, you also need to set up the relevant application software environment. Unlike the diskless network, all the terminal application software are It is installed on the server side. After successfully installing a software on the server, all terminals can use this software as if they were on the server. Everyone knows that installing software under Windows 98 or Windows NT 4.0 can be done easily by simply "Setup". However, if the installation file "Setup.exe" of the software is directly run on the Windows 2000 server, the system often displays a "Terminal Server Installation Failure" error message, and the installation cannot continue. Therefore, when installing software on a terminal server, you must first put the server in the installation state, but then install it, so that the software installation can continue normally. This means that the application software can be installed as in Windows 9x before adding Terminal Services. After adding Terminal Services, it cannot be installed this way. However, it is impossible to install all the applications in advance (for example, adding new software, application software upgrades, etc.) In general, the software installation after the terminal service is added can be performed as follows: double-click the "My Computer" icon; "My Computer" interface, then double-click the "Control Panel" icon, enter the "Control Panel" interface, find the "Add /Remove Programs" icon, double-click it, and enter the "Disc or Floppy" button. The "Install from the floppy disk or CD-ROM interface" appears, click "Next" to display the "Run Setup" interface, enter the path and file name of the installation file in the "Open" text box, click the "Next" button, then The installation wizard interface of the software appears, and then the same as the regular installation method, as long as the installation wizard can complete the software installation, most software, such as: Photoshop6.0, AutoCAD2000 WPS2000, NetAnts, Orient Express 2000 passed This installation method can complete the installation on the terminal server. Office2000, etc. must be installed in a special way.

(1) Installation of terminal input method

Windows 2000 Server comes with input methods such as full spell, Zheng code and smart ABC. If you need to add third-party input method, the following five-character word The description is as follows (note that many of the five-stroke input methods under Windows 9x are not working properly under Windows 2000. It is recommended to use the Wang code five-stroke input method in the office 2000 installation CD version 86)